Condition: Pre-Owned 127Bo
Reg. Price: [price_original_slashed_nobr]
Our Price: [price_for_sale]
Quantity [quantity_box_show]
In-Stock. May ship same day if ordered by 12pm.
Compatible Vehicles
FOR THIS FCC ID / PART #
Toyota 4 Runner
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
This is ONE (1) Dealer Installed Security System keyless remote control transmitter.
This is ONE (1) Dealer Installed Security System keyless remote control transmitter.
Specifications
Condition
Pre-Owned 127Bo
FCC ID
BAB237131-056
Part#
Dealer part #
PT398-07101
Buttons
4: Lock, Unlock, Aux, (Panic/on back)
Frequency
304 MHz / Red LED Light
Battery Type
1: CR2025
Additional Information
Condition Explanation: Pre-Owned
Pre-Owned = Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Scroll through listing for full details and description of any imperfections.
___________________________________
O.E.M. Toyota remote.
This remote fits the optional dealer or port-installed VIP RS3200 security system.
You must have this system on your vehicle. If you have the factory system, this remote will not work.
RS3200 systems were offered on many different Toyota Vehicles from 2000 and up.
Your current remote must look exactly like this one (with the LED light) and
have the same numbers on the back.
It is the customer's responsibility to determine if they have this system and to order the correct remote for their vehicle. Please make sure this is the remote you need.
_________________
Program Transmitter:
BAB237131-0256 / RS3200
TOYOTA TVIP SYSTEM PROGRAMMING-RS3200
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM
Follow this procedure to add additional remote controls to a system. The RS3200 may be programmed to operate with a maximum of four remote controls. When a new remote controls is programmed, it will work in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7 OF THE manual.
1. Before you begin:
Open the driver s door and remove the key from the ignition switch.
2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into, and remove it from the ignition switch 2 times.
b. Close, then open the driver s door 2 times.
c. Insert the key into, and remove it from the ignition switch 1 time.
d. Close, then open the driver s door 2 times.
e. Insert the key into, the ignition switch and leave it in.
f. Close the driver s door.
g. Turn the key from LOCK to ON, then back to LOCK.
h. Remove the key from the ignition switch.
i. The tail and marker lights flash 1 time, the buzzer chirps 1 time and the doors lock
and unlock 1 time.*
* If the system does not activate the lights, buzzer and door locks 1 time, start over.
3. Program (add) an additional remote control.
a. Press and release both the LOCK and UNLOCK buttons control at the same
time.
b. Press and release the LOCK button.
c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock
and unlock 1 time.*
Note: Repeat the above steps to add additional remote controls.
4. Complete the programming steps.
a. Open the driver s door
REPROGRAM EXISTING REMOTE CONTROLS
Follow this procedure to clear all existing remote control codes and reprogram existing remote controls to
a system. When existing remote controls are reprogrammed, they will work in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7.
1. Before you begin: Open the driver s door an
2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into, and remove it from the ignition switch 2
times.
b. Close, then open the driver s door 2 times.
c. Insert the key into, and remove it from the ignition switch 1 time.
d. Close, then open the driver s door 2 times.
e. Insert the key into, the ignition switch and leave it in.
f. Close the driver sdoor.
g. Turn the key from LOCK to ON 2 times (ending at LOCK).
h. Remove the key from the ignition switch.
i. The tail and marker lights flash 2 times, the buzzer chirps 2 times and the doors
lock and unlock 2 times.*
*If the system does not activate the lights, buzzer and door locks 2 times, start over.
3. Reprogram an existing remote control.
a. Press and release both the LOCK and UNLOCK buttons on one remote
control at the same time.
b. Press and release the LOCK button.
c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock
and unlock 1 time.*
Note: Repeat the above steps to program (add) additional remote controls.
4. Complete the programming steps.
a. Open the driver s door
All remotes include working batteries (except case-only purchases)
A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle
This remote is compatible.
This remote is not compatible.
