Hyundai Hyundai keyless remote FCC ID GOH-PCGEN2 Code Alarm key fob car starter control dealer installed - Pre-Owned Dealer Installed 6 button 174Apoz

This is ONE (1) ready to program with batteries installed Dealer Installed Aftermarket Original Equipment O.E.M. keyless remote control transmitter that will work with your vehicle's compatible system ONCE PROGRAMMED.

Please NOTE: you will receive EITHER of the remotes pictured - they both have the same exact circuit boards and will program the same.


Please NOTE: The logo on the front or the Make printed on the back of this remote will be NONE, FORD, KIA, HYUNDAI, or MAZDA

Compatibility: Match the FCC ID # on the back of your current remote to the FCC ID listed below.
--------------------------

WATCH THIS video for PROGRAMMING

https://www.youtube.com/watch?v=jReygK5hYFU


Programming: watch this VIDEO

https://www.youtube.com/watch?v=jReygK5hYFU

This remote will need to be programmed to your vehicle in order to work with your vehicle.
Programming Transmitter:

See PAGE 21 of Manual:

http://ww2.justanswer.com/uploads/jmcdo28/2008-12-30_042008_base.pdf
.......................

NOTE: Transmitters come pre-programmed with kit. If using transmitters that came with the kit, please ig
nore this section. Use this section to program replacement or additional transmitters only.

A.Open the driver s door
(press and hold in brake pedal on Remote Start only system - RMST)
NOTE:
On vehicles with negative polarity door ajar switch input circuits (Refer to the vehicle specific
programming section), the door is closed during this step unless the door ajar switch input polarity option
has been previously changed to negative.
B. Turn the ignition key to the ON or RUN position;
C. Press and hold the programming/override button;
After 10 seconds the horn will chirp 3 times, indicating the system is now in the transmitter learn mode.
D. Release the programming/override button;
E. Press transmitter button 1(
on RKE/VSS/RMST, except RMST system which is ) on the on the remote control
transmitter to be programmed.
The horn will chirp one time to indicate that the transmitter has been learned.
Notes:
A. Up to a total of 8 transmitters can be programmed at this time
B. Transmitters shipped with complete kits or personality kits are pre-programmed to the DNA and do not need to be
programmed at this time.
C. If the vehicle is equipped with memory seats/functions, the last two transmitters programmed will activate the
memory seats/functions.
D. All programmed transmitters can be erased from memory by pressing the door trim switch unlock button while in
transmitter learn mode (requires that the Disarm input and Unlock sense input wires be connected)


Programming Transmitter:

Method #1
_____________________

1. Open the driver side door
2. Lock and then unlock the door using the button on the door.
3. Leave the door open.
4. Insert a key into the ignition and turn the car to the ON position. Leave for about 2 or 3 seconds, then turn off. Repeat this two more times (3 in total). Leave the key in the slot in the OFF position.
5. Close the driver s door. Then open it. Then close it. Then open it. Then close it. Then open it.
6. The onboard computer will respond by locking and unlocking all the doors at this point. That means it s ready to accept FOB programming
7. Press a button on each FOB unit to program it to the computer.
When you are done programming FOBs, you can simply remove the key, which causes the computer to cycle the door locks once more.

Method #2
________________________
1. Remove key from ignition.
2. Close all doors
3. Open driver side door and leave open.
4. Perform the following steps within 24 seconds.
a. Insert key in ignition.
b. Turn key to ON and OFF.
c. Repeat step b two more times.
d. Remove key.
e. Push driver door frame button three times (black rubber button located on driver door frame that tell the vehicle whether or not door is closed.)
5. Buzz sound, chime or doors will lock and unlock should be heard at this point signaling that the vehicle is now in programming mode. If not, wait 40 seconds and return to step 4.
6. All transmitters need to be programmed at this time, including the old ones. Push any button on the transmitter two times. A buzz sound, chime or doors locking and unlocking should be heard at this point signaling that the vehicle has accepted the new transmitter code. If there is only one transmitter, repeat this step two more times using the only transmitter. If there are two transmitters, repeat this step two more times using the second transmitter.
7. Push driver door frame button one time. Two buzz sounds, chimes or doors locking and unlocking 2 times should be heard at this point signaling successful programming