Condition: Pre-Owned 636po
Reg. Price: [price_original_slashed_nobr]
Our Price: [price_for_sale]
Quantity [quantity_box_show]
In-Stock. May ship same day if ordered by 12pm.
Compatible Vehicles
FOR THIS FCC ID / PART #
This remote is compatible with the following installed aftermarket security systems:
Automate
Automate 6
Automate 7
Automate 10
Automate 25
Automate 35
Automate 410
Automate 425
Automate 435
Automate 52
Automate 53
Automate 552
Automate 553
Avital
Avital 2100
Avital 2200
Avital 2300
Avital 3100
Avital 3200
Avital 3300
Avital 4000
Avital 4100
Avital 4200
Avital 4300
Avital 4400
Maxx2
Maxx3
Hornet
Hornet 533 T
Hornet 554 T
Hornet 740 T
Hornet 742 T
Hornet 851 T
Python
Python 400 HP
Python 440 HP
Python 450 ESP
Python 460 HP
Python 500 HP
Python 625 HF
Python 650 ESP
Python 660 XP
Python 700
Python 900
Python 1000 HF
Python PC 1000 HF
Python 1200 XP
Python 1400 XP
Python 1500 HF
Python 1600 XP
Python 2000 HF
Python 3000 HF
Python 3000 ESP
Sidewinder
Sidewinder 3000 HF
Sidewinder 3000 ESP
Sidewinder 3200 HS
Sidewinder 3300 HS
Sidewinder 3500 ESP
Sidewinder 4500 HF
Sidewinder 5000 HF
Sidewinder 5000 ESP
Sidewinder 5500 XS
Sidewinder 6000 HF
Sidewinder 6000 ESP
Sidewinder 6500 HF
Sidewinder 6500 ESP
Sidewinder 7000 HF
Sidewinder 7000 ESP
Sidewinder PC 7000 SHF
Rattler
Rattler 100
Rattler 110 D
Rattler 200
Rattler 210 D
Rattler 250
Rattler 259 R
Rattler 300
Rattler 310 D
Rattler 359 R
Rattler 369 D
Valet
Valet 450 R
Valet 519 H
Valet 551 R
Valet 552 T
Valet 562 T
Valet 561 R
Valet 712 T
Valet 716 T
Merlin
Merlin 2000
Ungo
Ungo K10
Ungo K20
Ungo RK1
Ungo RS10
Ungo S100
Ungo S400
Ungo S660
Ungo S670
Ungo SR1000
Ungo SR5000
Ungo SR6000
Viper
Viper 100 HF (ESP)
Viper 130 HV
Viper 150 ESP
Viper 160 XV
Viper 210 HV
Viper 211 HV
Viper 300 HF
Viper PC 300 HF (ESP)
Viper 300+ HF
Viper 330 V
Viper 350 HV
Viper 500 HF
Viper PC 500 HF (ESP)
Viper 550 HF
Viper 550 HF (ESP)
Viper 560 XV
Viper 571 XV
Viper 600 HF
Viper PC 600 HF (ESP)
Viper 650 XV
Viper 671 XV
Viper 700 ESP
Viper 771 XV
Viper PC 800 SHF
Viper 800 SHF ESP
Viper 850 XV
Viper 1000
Viper 1002
Viper 3000
Viper 3002
Viper 5000
Viper 5002
Viper 7900
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
This is ONE (1) aftermarket keyless remote control transmitter. Attention: Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same. Compatibility 1: Please match this remote's FCC ID and part # to your current remote. Compatibility 2: Please match this remote's compatible aftermarket installed systems found in our Compatible Vehicles section below to your current installed system. Programming: Please Note: A Valet / Programming switch is required to program this remote. Programming can be difficult if you are not familiar with it. Please read the programming instructions (below) before purchasing. Assistance from an auto specialty shop or locksmith may be needed. Programming Instructions: The vehicle s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle s security system or to change button assignments if desired. In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain's Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere). The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit. 1) Open a door and make sure the dome light is on. 2) Turn the ignition on to the RUN position or you may also start car. 3) Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch. CHANNEL # FUNCTION 1 Arm / Disarm / Panic 2 Silent Mode / Remote Valet / Trunk Release 3 Remote Start or other accessories 4 Arm only (4 button remote) 5 Disarm only (4 button remote) 6 Panic only (4 button remote) 7 Auto Program single Arm Disarm Panic button configuration (4 button remote) 8 Auto Program this remote 9 Delete all transmitters CHANNEL 9: If any transmitter button from a known transmitter is programmed to channel 9, all transmitters will be erased from memory. This is useful in cases when one of the customer s transmitters is lost or stolen. This will erase any lost or stolen transmitters from your system s memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly. 4) You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release. If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter. 5) Once the code(s) are learned, the Valet/Program push button can be released. 6) Programming mode will be exited if one of the following actions occurs: a. Ignition key is turned to the OFF position b. Valet/Program switch is pressed too many times. c. More than 15 seconds elapses between programming steps. The horn will emit one long chirp when programming mode has been exited.
This is ONE (1) aftermarket keyless remote control transmitter. Attention: Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same. Compatibility 1: Please match this remote's FCC ID and part # to your current remote. Compatibility 2: Please match this remote's compatible aftermarket installed systems found in our Compatible Vehicles section below to your current installed system. Programming: Please Note: A Valet / Programming switch is required to program this remote. Programming can be difficult if you are not familiar with it. Please read the programming instructions (below) before purchasing. Assistance from an auto specialty shop or locksmith may be needed. Programming Instructions: The vehicle s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle s security system or to change button assignments if desired. In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain's Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere). The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit. 1) Open a door and make sure the dome light is on. 2) Turn the ignition on to the RUN position or you may also start car. 3) Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch. CHANNEL # FUNCTION 1 Arm / Disarm / Panic 2 Silent Mode / Remote Valet / Trunk Release 3 Remote Start or other accessories 4 Arm only (4 button remote) 5 Disarm only (4 button remote) 6 Panic only (4 button remote) 7 Auto Program single Arm Disarm Panic button configuration (4 button remote) 8 Auto Program this remote 9 Delete all transmitters CHANNEL 9: If any transmitter button from a known transmitter is programmed to channel 9, all transmitters will be erased from memory. This is useful in cases when one of the customer s transmitters is lost or stolen. This will erase any lost or stolen transmitters from your system s memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly. 4) You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release. If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter. 5) Once the code(s) are learned, the Valet/Program push button can be released. 6) Programming mode will be exited if one of the following actions occurs: a. Ignition key is turned to the OFF position b. Valet/Program switch is pressed too many times. c. More than 15 seconds elapses between programming steps. The horn will emit one long chirp when programming mode has been exited.
Specifications
Condition
Pre-Owned 636po
FCC ID
EZSDEI474V
Part#
SAA474U(Interchangeable Part # s)
470
474
475
476
485
820041
7143
26131
(Alternate Spelling )
EZSDE1474V
(Interchangeable FCC Id)
EZSDEI474
Dealer part #
Buttons
4: Lock, Unlock, Aux, Start; LED Green
Frequency
433 - 434 MHz
Battery Type
1: CR2032
Additional Information
Condition Explanation: Pre-Owned
Pre-Owned: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Scroll through listing for full details and description of any imperfections.
Why purchase a recycled keyless entry remote transmitter?
The vehicle keyless remote key fob you are going to purchase from us is pre-owned; aka: used, previously loved ;). We recycle OEM and aftermarket keyfobs and put them through a concise refurbishing process so we can guarantee our products are delivered to you in a ready-to-program state. We offer these car clickers at a significant cost savings to stealerships so you can keep your hard earned cash for something more fun while lightening your ecological footprint . We call that a win-win! Why wait? Add some convenience to your daily routine and help save the environment, order your recycled car remote control today!
All remotes include working batteries (except case-only purchases)
A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle