Condition: Pre-Owned LCD4Apo
Reg. Price: [price_original_slashed_nobr]
Our Price: [price_for_sale]
Quantity [quantity_box_show]
In-Stock. May ship same day if ordered by 12pm.
Compatible Vehicles
FOR THIS FCC ID / PART #
Compatible With the following Aftermarket installed security systems:
AS-2471TW-FM
AS2471TWFM
AS2471
AS476LCD
Nordic Start NS-2432TW-FM
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
This is for ONE (1) remote - it will look like either remote pictured... an aftermarket keyless remote control transmitter. Attention: Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same. PROGRAMMING INSTRUCTIONS: METHOD #1: ................... Transmitter Programming Procedure 1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory 2. 3. THE INSTALLER ... Press and hold the hood pin for 4 seconds. Release the hood pin (the parking lights will turn ON). Parking Lights 'ON" While the parking lights are on, press the hood pin once more and release immediately. 'ON" for 20 seconds You now have 20 seconds to select one of the sub-menus. To exit programming mode, dose the HOOD. Transmitter Programming Procedure 1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory. To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button ................... METHOD #2: ................... Loci$J Lun 0 to don, THE INSTALLER ... THE MODULE ... Press and hold the hood pin for 4 seconds. Release the hood pin (the parking lights will turn ON). Parking Lights 'ON" While the parking lights are on, press the hood pin once more and release immediately. 'ON" for 20 seconds You now have 20 seconds to select one of the sub-menus. To exit programming mode, dose the HOOD. Transmitter Programming Procedure 1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory. To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button (instead of LOCK or UNLOCK) in step 3 of the transmitter programming procedure 1. PLEASE REFER TO YOUR ORIGINAL OWNER S GUIDE FOR YOUR AFTERMARKET INSTALLED KEYLESS ENTRY SYSTEM OR 2. CONTACT A LOCAL CAR/AUDIO SHOP 3. CONTACT A LOCKSMITH 4. CONDUCT A GOOGLE SEARCH 5. CONTACT MANUFACTURER
This is for ONE (1) remote - it will look like either remote pictured... an aftermarket keyless remote control transmitter. Attention: Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same. PROGRAMMING INSTRUCTIONS: METHOD #1: ................... Transmitter Programming Procedure 1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory 2. 3. THE INSTALLER ... Press and hold the hood pin for 4 seconds. Release the hood pin (the parking lights will turn ON). Parking Lights 'ON" While the parking lights are on, press the hood pin once more and release immediately. 'ON" for 20 seconds You now have 20 seconds to select one of the sub-menus. To exit programming mode, dose the HOOD. Transmitter Programming Procedure 1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory. To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button ................... METHOD #2: ................... Loci$J Lun 0 to don, THE INSTALLER ... THE MODULE ... Press and hold the hood pin for 4 seconds. Release the hood pin (the parking lights will turn ON). Parking Lights 'ON" While the parking lights are on, press the hood pin once more and release immediately. 'ON" for 20 seconds You now have 20 seconds to select one of the sub-menus. To exit programming mode, dose the HOOD. Transmitter Programming Procedure 1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory. To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button (instead of LOCK or UNLOCK) in step 3 of the transmitter programming procedure 1. PLEASE REFER TO YOUR ORIGINAL OWNER S GUIDE FOR YOUR AFTERMARKET INSTALLED KEYLESS ENTRY SYSTEM OR 2. CONTACT A LOCAL CAR/AUDIO SHOP 3. CONTACT A LOCKSMITH 4. CONDUCT A GOOGLE SEARCH 5. CONTACT MANUFACTURER
Specifications
Condition
Pre-Owned LCD4Apo
FCC ID
EZSNAH5603
Part#
1513A-NAH5603
IC ID: 1513A-NAH5603
Model Number: AS476LCD, ASRF5603BC
Compatible Antenna Number:
ANT-FM TW 130, TW-130, TW130
Transmitting Frequency: 433MHz
Is this a 2 Way keyfob?: Yes
Dealer part #
Buttons
4: Lock, Unlock, Trunk Opener, Car Vehicle Engine Starter
Frequency
433 MHz (FM)
Battery Type
1: CR2025
Additional Information
Attention: Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same.
_____________________________
This remote needs to be programmed to your vehicle in order for it to work with your vehicle s installed RKE (remote keyless entry ) system:
...................
METHOD #1:
...................
Transmitter Programming Procedure
1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory
2.
3. THE INSTALLER ...
Press and hold the hood pin for 4 seconds. Release the hood pin (the parking lights will turn ON). Parking Lights 'ON"
While the parking lights are on, press the hood pin once more and release immediately.
'ON" for 20 seconds
You now have 20 seconds to select one of the sub-menus. To exit programming mode, dose the HOOD.
Transmitter Programming Procedure
1. Enter programming Mode (paged) the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position. 3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. 4. The transmitter has been stored in memory. 5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory.
To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button
...................
METHOD #2:
...................
1. PLEASE REFER TO YOUR ORIGINAL OWNER S GUIDE FOR YOUR AFTERMARKET INSTALLED KEYLESS ENTRY SYSTEM OR
2. CONTACT A LOCAL CAR/AUDIO SHOP
3. CONTACT A LOCKSMITH
4. CONDUCT A GOOGLE SEARCH
5. CONTACT MANUFACTURER
All remotes include working batteries (except case-only purchases)
A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle