Audiovox / Prestige / Pursuit / Pro Prestige 173BP keyless remote FCC ID ELVATNC car key fob starter APSRS3Z replacement keyfob cotnrol P/N: 118-1256 - Pre-Owned 548Epo

This is One 3 button metal 1-way aftermarket keyless remote control transmitter.

Attention: Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same.


Compatibility: Match the FCC ID on your current working remote to the FCC ID listed below.

or

Compatibility: Match the system type installed in your vehicle to one of the compatible systems listed to the RIGHT.

Programming Requirements: Scroll below to additional details.


Programming Instructions

Note: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds of the previous step. If the 15 second time limit expires between steps, the unit will automatically exit the program mode. This is indicated by a long chirp from the siren.

Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored.

1. Enter the vehicle and turn the ignition switch to the on position.


2. Press and release the valet push button switch three times.


a. Some systems may use a combination push-button LED switch. In these systems the push-button and the dash-mounted LED are one and the same.


3. The dash mounted LED will flash once and the siren will chirp once, indicating that the system is ready to accept programming of mode #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.


4. Press and hold the lock or lock/unlock button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

Repeat step 4 for each transmitter you wish to program.

Note: If your transmitter button has the lock/unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8.

5. Press and release the valet push button switch one time to advance to mode 2. The siren will chirp 2 times and the dash-mounted LED will flash 2 times, indicating that the unit is ready to accept programming for mode #2 which is only used for separate lock and unlock button transmitters and is the disarm/unlock/unlock 2 and panic.



6. Press and hold the unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

Repeat step 6 for each transmitter you wish to program.

7. Press and release the valet push button switch one time to advance to mode 3. The siren will chirp 3 times and the dash-mounted LED will flash 3 times, indicating that the unit is ready to accept programming for mode #3 which is the trunk release/alternate output mode of the system.



8. Press and hold the trunk/key symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

Repeat step 8 for each transmitter you wish to program.

9. Press and release the valet push button switch one time to advance to mode 4 if so equipped. The siren will chirp 4 times and the dash-mounted LED will flash 4 times, indicating that the unit is ready to accept programming for mode #4, optional device (where equipped).



10. Press and hold the option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

Repeat step 10 for each transmitter you wish to program.

11. Press and release the valet push button switch one time to advance to mode 5 if so equipped. The siren will chirp 5 times and the dash-mounted LED will flash 5 times, indicating that the unit is ready to accept programming for mode #5 optional device (where equipped).



12. Press and hold the second option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

Repeat step 12 for each transmitter you wish to program.

13. Within 10 seconds, press and release the valet program switch one time. The siren will emit 6 short chirps indicating mode 6 has been entered.



14. Within 10 seconds, press and hold the unlock button, or any unused button(s), of the first transmitter you wish to control mode 6 output (Driver Priority 1), until a long chirp is heard from the siren.

Repeat this for each transmitter you wish to operate the mode 6 output, Driver Priority 1.

15. Within 10 seconds, press and release the valet program switch one time. The siren will emit 7 short chirps indicating mode 7 has been entered.

16. Within 10 seconds, press and hold the unlock button or any unused button(s) of the first transmitter you wish to control mode 7 output (Driver Priority 2), until a long chirp is heard from the siren.

Repeat this for each transmitter you wish to operate the mode 7 output, Driver Priority 2.

Note: Mode 6 & 7 can be used as separate output to control a function other than driver priority. Simply programming any unused transmitter button other than the unlock button will allow complete independent control of these outputs.