Compatible Vehicles
FOR THIS FCC ID / PART #
Dodge Viper
Years: 1998 1999 2000 2001 2002
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
One (1) New replacement remote control that will program to your vehicle's installed O.E.M. Original Equipment Manufacturer Factory RKE System.
Compatibility: FCC ID/Part number MUST match with original.
Programming Requirements:
2000 Dodge Viper
Programming Notes:
Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
If necessary, disarm the security system with a functioning remote.
Keyless Entry System Memory Clearing Instructions are noted in the dark blue colored steps below.
Step-by-Step How To Programming Instructions:
1. LOCATE the Data Link Connector (DLC) under the Driver s side dashboard. Use the diagram above to IDENTIFY Pins 1 and 4.
2. JUMP the Data Link Connector using a suitable groundwire from Pin 1 to Pin 4. DO NOT
3. REMOVE the jumper wire until the end of the programming process.
4. INSERT a key into the Ignition and TURN the Ignition to the ON position (just before cranking). If the jumper wire is correctly installed, the Alarm LED located top-center of the dash will flash to indicate entry into Programming Mode.
5. PRESS both the LOCK and UNLOCK buttons on the first remote to be programmed for approximately fifteen (15) seconds. The Vehicle s horn will sound three (3) times to indicate successful programming of the remote.
6. REPEAT Step 4 within 60 seconds for any additional remotes to be programmed to your Vehicle.
7. REMOVE the jumper wire, TURN the Ignition to the OFF position and REMOVE the key from the Ignition.
8. Test all remotes. Programming is now complete.
9. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
One (1) New replacement remote control that will program to your vehicle's installed O.E.M. Original Equipment Manufacturer Factory RKE System.
Compatibility: FCC ID/Part number MUST match with original.
Programming Requirements:
2000 Dodge Viper
Programming Notes:
Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
If necessary, disarm the security system with a functioning remote.
Keyless Entry System Memory Clearing Instructions are noted in the dark blue colored steps below.
Step-by-Step How To Programming Instructions:
1. LOCATE the Data Link Connector (DLC) under the Driver s side dashboard. Use the diagram above to IDENTIFY Pins 1 and 4.
2. JUMP the Data Link Connector using a suitable groundwire from Pin 1 to Pin 4. DO NOT
3. REMOVE the jumper wire until the end of the programming process.
4. INSERT a key into the Ignition and TURN the Ignition to the ON position (just before cranking). If the jumper wire is correctly installed, the Alarm LED located top-center of the dash will flash to indicate entry into Programming Mode.
5. PRESS both the LOCK and UNLOCK buttons on the first remote to be programmed for approximately fifteen (15) seconds. The Vehicle s horn will sound three (3) times to indicate successful programming of the remote.
6. REPEAT Step 4 within 60 seconds for any additional remotes to be programmed to your Vehicle.
7. REMOVE the jumper wire, TURN the Ignition to the OFF position and REMOVE the key from the Ignition.
8. Test all remotes. Programming is now complete.
9. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Specifications
Condition |
New 014Bno |
FCC ID |
ABO1302T FCCID: ABO1302T | AB01302T |
Part# |
4865431AA
4865431 AA R4L6546
A8O1302T AB0130ZT ABO13O2T, AB01302T 4865431 AA A801302T ABO1302T, ABO1302T 4865431AA
For FCC ID: ABO1302T
|
Dealer part # |
4865431AA |
Buttons |
2: Lock, Unlock |
Frequency |
315 MHz |
Battery Type |
1: CR2032 |
Additional Information
- All remotes include working batteries (except case-only purchases)
- A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
Compatible Vehicles
FOR THIS FCC ID / PART #
Dodge Viper
Years: 1998 1999 2000 2001 2002