Compatible Vehicles
FOR THIS FCC ID / PART #
Dodge Stratus 2 door
Years: 2002 2003 2004 2005 2006
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
This is a OEM Genuine Original Equipment Manufacturer Factory Installed keyless remote control transmitter.
Compatibility 1: FCC ID/Part number MUST match with original. Compatibility
2: Original MUST look identical with same buttons.
_________________
Programming Instructions:
1. Locate the Data Port under drivers side dashboard usually located to the right of steering column.
2. Insert keys in ignition and leave in the OFF position.
3. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port terminals 1 and 4 with a suitable jumper wire, leave the jumper wire connected throughout the programming procedure. Make sure you
know which terminals are 1 and 4.
4. Within 10 seconds after connecting the jumper wire, press the Hazard Switch 6 times. Note: The doors will automatically lock and unlock once at this time indicating that the system is in the programming mode.
5. Press the LOCK button on the remote to be registered three times within 10 seconds. Upon successful programming, the door will lock and unlock once.
6. Repeat step 5 with up to 4 remotes (including any existing remotes) within one minute. After completing each programming, the doors will lock and unlock once.
7. Disconnect the programming wire and remove the keys from the ignition.
This is a OEM Genuine Original Equipment Manufacturer Factory Installed keyless remote control transmitter.
Compatibility 1: FCC ID/Part number MUST match with original. Compatibility
2: Original MUST look identical with same buttons.
_________________
Programming Instructions:
1. Locate the Data Port under drivers side dashboard usually located to the right of steering column.
2. Insert keys in ignition and leave in the OFF position.
3. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port terminals 1 and 4 with a suitable jumper wire, leave the jumper wire connected throughout the programming procedure. Make sure you
know which terminals are 1 and 4.
4. Within 10 seconds after connecting the jumper wire, press the Hazard Switch 6 times. Note: The doors will automatically lock and unlock once at this time indicating that the system is in the programming mode.
5. Press the LOCK button on the remote to be registered three times within 10 seconds. Upon successful programming, the door will lock and unlock once.
6. Repeat step 5 with up to 4 remotes (including any existing remotes) within one minute. After completing each programming, the doors will lock and unlock once.
7. Disconnect the programming wire and remove the keys from the ignition.
Specifications
Condition |
Pre-Owned Dodge 4 btn 192dpo |
FCC ID |
OUCG8D-525M-A |
Part# |
G8D-525M-A or G8D-525M-A8 |
Dealer part # |
MR587981 |
Buttons |
4 (Lock, Unlock, Trunk, Panic) |
Frequency |
314 MHz |
Battery Type |
1: CR2032 |
Additional Information
Condition Explanation: Pre-Owned
Pre-Owned: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Scroll through listing for full details and description of any imperfections.
_________________
Programming Instructions:
1. Locate the Data Port under drivers side dashboard usually located to the right of steering column.
2. Insert keys in ignition and leave in the OFF position.
3. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port terminals 1 and 4 with a suitable jumper wire, leave the jumper wire connected throughout the programming procedure. Make sure you
know which terminals are 1 and 4.
4. Within 10 seconds after connecting the jumper wire, press the Hazard Switch 6 times. Note: The doors will automatically lock and unlock once at this time indicating that the system is in the programming mode.
5. Press the LOCK button on the remote to be registered three times within 10 seconds. Upon successful programming, the door will lock and unlock once.
6. Repeat step 5 with up to 4 remotes (including any existing remotes) within one minute. After completing each programming, the doors will lock and unlock once.
7. Disconnect the programming wire and remove the keys from the ignition.
- All remotes include working batteries (except case-only purchases)
- A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
Compatible Vehicles
FOR THIS FCC ID / PART #
Dodge Stratus 2 door
Years: 2002 2003 2004 2005 2006