Condition: New 3btn 087BUKno
Reg. Price: $256
Our Price: $34.99
Quantity
In-Stock. May ship same day if ordered by 12pm.
Compatible Vehicles
FOR THIS FCC ID / PART #
Buick Enclave w/ Engine Start, Power Liftgate Years: 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
This is ONE (1) keyless remote control transmitter that will program to your vehicle's compatible Factory Original Equipment O.E.M. installed RKE system. Compatibility: The remote FCC ID is the only important number on this remote - please make sure you need FCC ID OUC60270 or OUC60221 (look on the back of your current remote) (If the back of your remote reads FCC ID: KOBGT04A this is NOT correct.) Programming: You will need to program this remote to your vehicle in order for it to work with your vehicle. You will need the remote and the vehicle together to perform programming. Please scroll below to additional details for more information on programming or click the PROGRAM TAB above to locate the program requirements for your vehicle.
This is ONE (1) keyless remote control transmitter that will program to your vehicle's compatible Factory Original Equipment O.E.M. installed RKE system. Compatibility: The remote FCC ID is the only important number on this remote - please make sure you need FCC ID OUC60270 or OUC60221 (look on the back of your current remote) (If the back of your remote reads FCC ID: KOBGT04A this is NOT correct.) Programming: You will need to program this remote to your vehicle in order for it to work with your vehicle. You will need the remote and the vehicle together to perform programming. Please scroll below to additional details for more information on programming or click the PROGRAM TAB above to locate the program requirements for your vehicle.
Specifications
Condition
New 3btn 087BUKno
FCC ID
OUC60270 and OUC60221
Part#
15913420
GM P/N:
37180-78J20 3718078J20 or 15913420 or 20868852 or
20669056 or 20869056 or 22936099 or 20952475 or 25836192
all above part numbers are interchangeable
Interchangeable FCC ID "'s: OUC60270 or OUC60221
GM Interchangeable Numbers --- IC#: CAN: 850K60270 or 850K60221
Dorman Part #'s: 13621, 13716, 99161
Dealer part #
20952475
Buttons
3: Lock, Unlock, Panic
Frequency
315 MHz
Battery Type
1: CR2032
Additional Information
PROGRAMMING: The remote you purchase needs to be programmed to work on your vehicle. You can do this yourself UP TO model year 2010. Those instructions are included. Starting in 2011 Chevrolet removed the on-board programming and you will have to take your vehicle to a dealer or locksmith to have them programed with diagnostic equipment. Also see note below:
Programming Notes: Suzuki XL-7 & Saturn Vue do not come with programming instructions. You will need to go a dealership or automotive locksmith for programming. Also starting in 2011 GM took away the on board programming option for all vehicles. Vehicles 2011 & up will need to go to a dealership or automotive locksmith to program the remote.
................................
Programming Requirements:
________________________________
2007 2008 2009 2010 GMC ACADIA & 2007 2008 2009 Cadillac SRX PROGRAMMING REQUIREMENTS:
...................
This information is in your Owners Manual in the
Drivers Information Center Section.
.........................
1. Insert Key and turn to ON position so you can access Driver Information Center
2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays
3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays
4. Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.On vehicles with memory recall seats, the first remote learned will match Driver 1 and the second will match Driver 2.
5. To program additional remotes at this time repeat step 3.This vehicle can have a maximum of eight remotes programmed.
6. To exit programming mode turn key off and remove key.
Test remote(s).
_________________________________
2010 2011 Cadillac SRX PROGRAMMING REQUIREMENTS:
..............................
You have one programmed remote and you want to add another.
........................
1. Vehicle must be off.
2. Place the working remote(s) in the cupholder. Have the new remote with you.
3. Insert the key into the key lock cylinder located on the outside of drivers door.
4.Turn the key to the unlock position five times with in ten seconds.
5. The (DIC) Driver Information Center displays Ready to Learn Electronic key #2, 3, 4 ETC.
6. Place the new remote into the transmitter pocket with the buttons facing the front of the vehicle. (The transmitter pocket is inside the center console between the driver and front passenger seats). The storage area will need to be opened and the storage tray lifted up to access the transmitter pocket.
7. Press the ignition. When the remote is learned the DIC display will show that it is ready to program the next remote.
8. Remove the remote from the transmitter pocket and press unlock on the remote.
9. To program additional remotes, repeat Steps 6 through 8.
10. When all additional transmitters are programmed, press and hold the ignition for ten seconds to exit programming mode.
....................................
You have no working remotes.
.......................
1. The vehicle must be off.
2. Insert the key into the key lock cylinder located on the outside of drivers door.
3.Turn the key to the unlock position five times with in ten seconds.
4. The (DIC) Driver Information Center displays REMOTE LEARN PENDING, PLEASE WAIT.
5. Wait for ten minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press the ignition. The DIC displays will again show REMOTE LEARN PENDING, PLEASE WAIT.
6. Repeat Step 5 two additional times. After the third time all previously known remotes will no longer work with the vehicle. Remaining remotes can be relearned during the next steps. The DIC display should now show READY FOR REMOTE #1
7. Place the new remote into the transmitter pocket with the buttons facing the front of the vehicle. (The transmitter pocket is inside the center console between the
driver and front passanger seats). The storage area will need to be opened and the storage tray lifted up to access the transmitter pocket.
8. Press the ignition. When the remote is learned the DIC display will show that it is ready to program the next remote.
9. Remove the remote from the transmitter pocket and press unlock on the remote.
10. To program additional remotes, repeat Steps 7 through 9.
11. When all additional transmitters are programmed, press and hold the ignition for ten seconds to exit programming mode.
_________________________________
2008 2009 2010 BUICK ENCLAVE & CHEVY TRAVERSE PROGRAMMING REQUIREMENTS:
.......................
Drivers Information Center Section.
...........................
1. Insert Key and turn to ON position so you can access Driver Information Center
2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays
3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays
4. Press and hold the lock and unlock buttons on the keyless remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.
5. To program additional remotes at this time repeat step 4.
This vehicle can have a maximum of eight remotes programmed.
6. To exit programming mode turn key off and remove key.
Test remote(s).
..............................
Use this Procedure for Vehicles without
Drivers Information Center Buttons
.........................
To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)
1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display
3. Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.
4. To program additional remotes at this time repeat step 3.This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).
________________________________________
2011 2012 2013 BUICK ENCLAVE & CHEVY TRAVERSE & GMC ACADIA PROGRAMMING REQUIREMENTS:
The manufacturer programming requirements state:
There is no manual on board procedure to program a keyless remote to this vehicle. This vehicle requires special equipment be connected to the vehicle to program the remote. Please visit your local locksmith.
>>>>>>>>>>>>>>>>>>>>>>
2007 New Body Style Programming Instructions
Use this Procedure for Vehicles with Driver Information Center Buttons
1. Insert Key and turn to ON position so you can access Driver Information Center
2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays
3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays
4. Press and hold the lock and unlock buttons on the keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.
5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.
6. To exit programming mode turn key off and remove key. Test remote(s).
________________________________________
Use this Procedure for Vehicles without Drivers Information Center Buttons
To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).
1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display.
3. Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.
4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key. Test remotes.
All remotes include working batteries (except case-only purchases)
A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle
Unsure if this is compatible with your vehicle?
Your vehicle may need a different FCC ID / Part Number depending on your installed Remote Keyless Entry System (RKE): Factory, Dealer or Aftermarket. If you are unsure what system is installed, check your current remote, send us a photo, or contact us.
check compatibility
Compatible Vehicles
FOR THIS FCC ID / PART #
Buick Enclave w/ Engine Start, Power Liftgate Years: 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017